Ensemble-designs 8500 Composite / SD Legalizer and Video Processing Manual do Utilizador

This data pack provides detailed installation, configuration and operation information forthe 8500 Series Video Processing Synchronizer module along w

8500-10INSTALLATIONRear Module BNC ConfigurationThere are three configurable rear BNC connectors that can be set using onboard switcheson the rear of

CABLINGRefer to the 3 RU and 1 RU Backplane with 8410 and 8510 Audio Submodule or 3 RU and 1 RU Backplane with 8415 Audio Submodule diagrams on the fo

Analog Audio8500 VAPAES 3/4 Out /SDI OutAES 1/2 Out/SDI OutAES 1/2 In C/Pr InCpst/Y/Pb InCpst/SDI OutAES 3/4 In Ref InSDI OutSDI/Y In16++++----11AUD 2

Analog Audio – Use the AnalogAudio 15-pin D connector forcabling analog audio inputs oroutputs when the 8510 option isinstalled. Refer to the pinoutdi

8500-14MODULE CONFIGURATION AND CONTROLThe configuration parameters for each Avenue module must be selected after installation.This can be done remote

8500-15Model 8500 Series ModulesA Detail Enhancer recovers information that has been lost due to poor frequency responsein upstream systems.Selective

• Blanking: There are Wide, Narrow or Custom blanking choices. Wide givesblanking through line 20 (NTSC) or line 22 (PAL), while narrow produces blank

8410, 8415, and 8510 Audio Processor ConfigurationThe 8510 Audio Processor will accept audio from analog or AES input connectors and candisembed audio

the normal audio functions and is carried to the AES output formatter anddriver. When in the Data mode, the AES formatter is driven by the output timi

Audio Operational ExamplesThis section describes the audio configuration of the application examples given at thebeginning of this manual. Both the 84

8500 SERIES OVERVIEWThe 8500 Video Processing Frame Synchronizer, along with its optional submodules,provides a real "do it all" module. A b

Audio Example 3: Here stereo audio embedded on an SDI stream is arriving viamicrowave, but lip sync is off by about 65mS due to video passing through

8520 Digital Noise Reducer ConfigurationThe 8520 DNR is motion and scene adaptive. It removes unwanted noise and artifacts,making it perfect for MPEG

8500-22Model 8500 Series Modules8500 Parameter TableCONTROL LOCAL REMOTEFACTORYDEFAULTDEFAULTUSER LEVELVIDEO IN/PROCESSING CONTROLSInput SelectSwitch

Model 8500 Series ModulesCONTROL LOCAL REMOTEFACTORYDEFAULTDEFAULTUSER LEVELDNR CONTROLS (8520 DNR submodule installed)DNR ModeSwitch 6:On (AutomaticL

Model 8500 Series Modules8500-24CONTROL LOCAL REMOTEFACTORYDEFAULTDEFAULTUSER LEVELVIDEO OUTPUT CONTROLSBypass NormalNormalBypassSplitSplit DNRNormal

CONTROL LOCAL REMOTEFACTORYDEFAULTDEFAULTUSER LEVELAUDIO CONTROLS (8410, 8415 or 8510 Audio Submodule Installed)Ch 1-4 In (level) –70 dB –70 to +12 dB

CONTROL LOCAL REMOTEFACTORYDEFAULTDEFAULTUSER LEVELAUDIO CONTROLS (8410, 8415 or 8510 Audio Submodule Installed)Audio Embed ReplaceOffReplaceCascadeRe

Front Panel Controls and IndicatorsEach front edge indicator and switch setting is shown in the diagram below:Remote/Local switch:Set to the mode youw

Avenue PC Remote ConfigurationThe Avenue PC remote control menus for this module are illustrated and explained below.Refer to the 8500 Parameter Table

Model 8500 Series ModulesThe Proc menu shown below allows you to adjust the following video processing parame-ters for the signal:• Gain – adjust the

chroma, pedestal, and hue knobs, live shading is easy. The continuous rotation velocitysensitive knobs are responsive and dependable. Audio levels for

Use the Clip menu shown below to adjust the following parameters:• Legalizer – set the legalizer function to one of the following:Off – to disable it.

The DNR menu allows you to adjust the following noise reducer parameters for the signalwhen the 8520 DNR submodule is installed:• Mode – set the mode

Adaptive – this mode requires manual settings of all parameters. Finedetail is preserved and motion is removed. Best used for signals with lessmotion

• Luma – set to On to enable the Luma control or Off to disable. The luma channelcan be adjusted independently of the chroma channel for noise reducti

8410 and 8510 Audio Processor SubmodulesWhen an 8410 or 8510 Audio Processor submodule is installed, use the Aud Mix menushown below to control the au

Use the Aud In menu shown below for the 8410 and 8510 to adjust the following parame-ters:• 1/2 Input – select the input audio source for Input 1/2.•

8415 Audio Processor SubmoduleWhen an 8415 Audio Processor submodule is installed, use the Aud Mix A and B menusshown to control the audio mixing and

For Channels 5 –8, use the Audio Mix B menu shown below to set the following• Input Ch 5 – assign Input Channel 5 to the desired output bus or tie to

Use the Aud In A menu shown below for the 8415 to adjust the following parameters:• 1/2 Input – select the input audio source for Input 1/2.• 3/4 Inpu

Use the Aud In B menu shown below for the 8415 to adjust the following parameters:• 5/6 Input – select the input audio source for Input 5/6.• 7/8 Inpu

One of three types of Audio Processing submodules can be installed on the 8500 module.The audio processors have also been designed to provide superior

Use the Aud Delay menu shown below for all versions of Audio submodule to adjust theamount of audio delay on the output:• Auto Track – enable auto tra

8415: Use the Aud Out menu shown below to adjust the following audio output parameters:• Audio Embed A – turn embedding Off for no embedding to take p

The Filter menu shown below allows setting of the luminance and chroma sharpness(with DNR option) with the following detail enhancing controls:• Lum S

The Blanking menu shown below allows you to adjust the output blanking of the modulewith the following controls:• Mode – set the blanking mode to Narr

Model 8500 Series ModulesUse the Vid Out menu shown below to adjust the following parameters:• Bypass – set to Normal for no split screen, Bypass to c

8500-45Model 8500 Series ModulesOutput Menu Bypass SettingDNR Menu Bypass SettingOutput ConditionsNormalNormal All processing on.Bypass All DNR proces

Model 8500 Series Modules8500-46The Memory menu shown below allows you to save overall module setups to five memoryregisters as follows:• Select Save,

Avenue Touch Screen Remote ConfigurationThe Avenue Touch Screen remote control status menu for this module is illustrated andexplained below. Refer to

The Proc menu shown below allows you to adjust the following video processing parame-ters for the signal:• Gain – adjust the percentage of overall gai

8500-49Model 8500 Series ModulesUse the Clip menu shown below to adjust the following parameters:• Legalizer – set the legalizer function to one of th

The 8415 Audio Processor submodule shown below provides eight channels of digitalaudio processing. Digital audio inputs to the 8415 can come from four

The DNR menu allows you to adjust the following noise reducer parameters for the signalwhen the 8520 DNR submodule is installed:• Mode – set the mode

8500-51Model 8500 Series ModulesAdaptive – this mode requires manual settings of all parameters. Fine detailis preserved and motion is removed. Best u

• Luma – set to On to enable the Luma control or Off to disable. The luma channelcan be adjusted independently of the chroma channel for noise reducti

8410 and 8510 Audio Processor SubmodulesWhen an 8410 or 8510 Audio Processor submodule is installed, use the Aud Mix menushown below to control the au

Use the Aud In menu shown below for the 8410 and 8510 to adjust the following parame-ters:• 1/2 Input – select the input audio source for Input 1/2.•

8415 Audio Processor SubmoduleWhen an 8415 Audio Processor submodule is installed, use the Aud Mix menus shown onthe next page to control the audio mi

For Channels 5 –8, use the Audio Mix B menu shown below to set the following• Input Ch 5 – assign Input Channel 5 to the desired output bus or tie to

Use the Aud In A menu shown below for the 8415 to adjust the following parameters:• 1/2 Input – select the input audio source for Input 1/2.• 3/4 Inpu

Use the Aud In B menu shown below for the 8415 to adjust the following parameters:• 5/6 Input – select the input audio source for Input 5/6.• 7/8 Inpu

Use the Aud Delay menu shown below for all versions of Audio submodule to adjust theamount of audio delay on the output:• Auto Track – enable auto tra

Model 8500 Series Modules8500-6APPLICATIONSThis section provides some typical applications for utilizing the full versatility of the 8500Video Process

8410 and 8510: Use the Aud Out menu shown below to adjust the following audio outputparameters:• Audio Embed – turn embedding Off for no embedding in

8415: Use the Aud Out menu shown below to adjust the following audio output parameters:• Audio Embed A – turn embedding Off for no embedding to take p

The Filter menu shown below allows setting of the luminance and chroma sharpness(with DNR option) with the following detail enhancing controls:• Lum S

Use the Timing menu shown below to adjust the following parameters:• Fine Phase – adjust for proper ScH phase with respect to other sources. If fineph

The Blanking menu shown below allows you to adjust the output blanking of the modulewith the following controls:• Mode – set the blanking mode to Narr

Use the Vid Out menu shown below to adjust the following parameters:• Bypass – set to Normal for no split screen, Bypass to completely bypass anydigit

The Memory menu shown below allows you to save overall module setups into up to fivememory registers as follows:• Select Save, then one of the five me

The Trim menu allows you to correct subtle issues in the individual color differencechannels with offset and gain controls. The offset controls adjust

8500-68TROUBLESHOOTINGAs a troubleshooting aid, the reference signal status and presence, power and CPU statuscan be easily monitored from the front p

WARRANTY AND FACTORY SERVICEWarrantyThis module is covered by a five year limited warranty, as stated in the main Preface ofthis manual. If you requir

Compact SystemsA one rack unit (1 RU) Avenue chassis populated with a 5400 TSG and one or two 8500Series modules makes an ideal signal acquisition sys

SPECIFICATIONS8500 Video ProcessorAnalog InputsType: SMPTE Y, Cr, CbBeta Y, Cr, CbNTSC, PAL CompositeNTSC, PAL S-Video (Y/C)Impedance: 75 Ω, BNCReturn

Analog OutputType: NTSC or PAL CompositeStandard follows inputImpedance: 75 Ω, BNCReturn Loss: > 40 dBOutput DC: < 50 mVSerial Digital Output(s)

8410 Audio ProcessorAES/EBU Digital InputsNumber: 2 (Total of four channels)Type: AES3idConnectorization: Coaxial, 75 Ω BNCBit Depth: 20 or 24 BitSamp

8415 Audio ProcessorAES/EBU Digital InputsNumber: 4 (Total of eight channels)Type: AES3idConnectorization: Coaxial, 75 Ω BNCBit Depth: 20 or 24 BitSam

8510 Audio ProcessorAnalog InputsNumber: Configurable as 2 or 4Type: BalancedImpedance: > 15k ΩMaximum Input Level: 24 dBuCMRR: > 60dB, 20Hz to

AES/EBU Digital OutputsNumber: 2 (Total of four channels)Type: AES3idConnector Type: Coaxial, 75 Ω BNCBit Depth: 20 or 24 BitSample Rate: 48 kHzSynchr

Model 8500 Series Modules8500-76

Model 8500 Series ModulesNews/ENG VehicleThe wide variety of input feeds often encountered can be easily handled with an Avenue8500 based system. Inpu

Model 8500 Series ModulesRemote Truck/OB Van OperationA convenient and flexible interconnect to a Remote Truck or OB Van is assured with useof the 850