Ensemble-designs 7900 HD Up/Down/Cross Converter Manual do Utilizador

This data pack provides detailed installation, configuration and operation information forthe 7900 HD Up/Down/Cross Converter module as part of the Av

MODULE CONFIGURATION AND CONTROLThe configuration parameters for each Avenue module must be selected after installation.This can be done remotely usin

Model 7900 HD Up/Down/Cross Converter7900 Parameter TableCONTROL LOCAL REMOTEFACTORYDEFAULTDEFAULTUSER LEVELReference Source Ext RefExt RefMaster RefV

7900 Parameter TableCONTROL LOCAL REMOTEFACTORYDEFAULTDEFAULTUSER LEVELWidth (Manual) 100% +/ – 100% 100% AdminHeight (Manual) 100% +/ – 100% 100% Adm

CONTROL LOCAL REMOTEFACTORYDEFAULTDEFAULTUSER LEVELCpst Out Setup OffOffOnOff Level 2Ch 1-8 In (level) 0 dB –70 to +12 dB 0 dB Level 1Ch 1-8 Output Bu

7900-14CONTROL LOCAL REMOTEFACTORYDEFAULTDEFAULTUSER LEVELMux Group A and BGroup 1Group 1Group 2Group 3Group 4Group 1 Level 1Dig Ref Level –20 dBFS–20

Front Panel Controls and IndicatorsThe front edge indicators and switch settings are shown in the diagram below:7900-15Video In green LED:ON indicates

Model 7900 HD Up/Down/Cross ConverterAvenue PC Remote ConfigurationThe Avenue PC remote control menus for this module are illustrated and explained be

The Mode menu allows you to configure the following:• Mode – indicates the mode in which the unit is running (Upconvert,Downconvert, Cross Convert, AR

Model 7900 HD Up/Down/Cross ConverterWhen Manual is selected in the Mode menu, you may set the output format mode of theupconverted HD output with the

The Proc menu shown below allows you to adjust the following video processing parametersfor the signal:• Gain – adjust the percentage of overall gain

MODULE OVERVIEWThe 7900 module is a flexible, configurable up and downconverter for use in broadcast andpost-production. It can process SD (Standard D

Use the Vid Out menu shown below to adjust the following parameters:• Vert Blanking – set the blanking mode to Narrow (lines 1-9 are blanked inNTSC, l

When an 8415 Audio Processor submodule is installed, use the Aud Mix A and B menusto control the audio mixing and shuffling of the module. Each output

For Channels 5 – 8, use the Audio Mix B menu shown below to set the following• Input Ch 5 – assign Input Channel 5 to the desired output bus or tie to

Use the Aud Delay menu shown below for the 8415 Audio submodule to adjust theamount of audio delay on the output:• Auto Track – enable auto tracking b

Use the Aud In A menu to adjust the following parameters:• 1/2 Input – select the input audio source for Input 1/2.• 3/4 Input – select the input audi

7900-25Use the Aud In B menu to adjust the following parameters:• 5/6 Input – select the input audio source for Input 5/6.• 7/8 Input – select the inp

Use the Aud Out menu to adjust the following audio output parameters:• Audio Embed A – turn embedding Off for no embedding to take place in theoutput

The MetaData menu reports or provides settings for the following closed captioning andtimecode parameters:• CC Input Line – You do not need to set the

The Memory menu allows you to save overall module setups to five memory registers asfollows:• Select Save, then one of the five memory registers Reg 1

Avenue Touch Screen Remote ConfigurationThe Avenue Touch Screen remote control menus for this module are illustrated andexplained below. Refer to the

7900-37900 HD Up/Down/Cross Converter Functional Block Diagram, Landscape ViewModel 7900 HD Up/Down/Cross Converter

The Mode menu allows you to configure the following:• Mode – indicates the mode in which the unit is running (Upconvert,Downconvert, Cross convert, AR

When Manual is selected in the Mode menu, you may set the output format mode of theupconverted HD output with the following controls: Manual• Width –

Use the Config menu below to enable the following controls: • Noise Reduce – adjusts the amount of noise reduction on the output signalfrom Off, Low,

The Proc menu allows you to adjust the following video processing parameters for thesignal:• Gain – adjust the percentage of overall gain (luminance a

Use the Vid Out menu shown below to adjust the following parameters:• Vert Blanking – set the blanking mode to Narrow (lines 1-9 are blanked inNTSC, l

When an 8415 Audio Processor submodule is installed, use the Aud Mix A and B menusshown next to control the audio mixing and shuffling of the module.

For Channels 5 – 8, use the Audio Mix B menu shown below to set the following• Input Ch 5 – assign Input Channel 5 to the desired output bus or tie to

Model 7900 HD Up/Down/Cross Converter7900-37Use the Aud Delay menu shown below for the 8415 Audio submodule to adjust theamount of audio delay on the

Use the Aud In A menu to adjust the following parameters:• 1/2 Input – select the input audio source for Input 1/2.• 3/4 Input – select the input audi

Use the Aud In B menu to adjust the following parameters:• 5/6 Input – select the input audio source for Input 5/6.• 7/8 Input – select the input audi

7900-47900 HD Up/Down/Cross Converter Functional Block Diagram, Portrait ViewModel 7900 HD Up/Down/Cross Converter

Use the Aud Out menu shown below to adjust the following audio output parameters:• Audio Embed A – turn embedding Off for no embedding to take place i

The MetaData menu below allows you to set the following closed captioning and time-code parameters:• CC Input Line – You do not need to set the value

The Memory menu shown below allows you to save overall module setups to five memoryregisters as follows:• Select Save, then one of the five memory reg

TROUBLESHOOTINGAs a troubleshooting aid, the signal presence, power and CPU status can be easily monitored from the front panel of this module using t

WARRANTY AND FACTORY SERVICEWarrantyThis Module is covered by a five year limited warranty. If you require service (under warranty or not), please con

7900-45SPECIFICATIONS7900 HD Up/Down/Cross ConverterSerial Digital Input:Number: OneSignal Type: HD Serial Digital 1.485 Gb/sSMPTE 274M, 292M or 296Mo

Analog Video Output (when SD output is configured for composite) Number: Two Maximum(BNCs shared with SD SDI outputs)Type: NTSC or PAL CompositeStanda

Embedded InputsNumber: Four AES Streams (from video input)Eight channels from any two of four groupsSelectable to any of four groupsType: SMPTE 274M C

Automatic Aspect Ratio Conversion – The 7900 supports WSS (Wide ScreenSignaling), AFD (Active Format Description) to mark or identify the aspect ratio

APPLICATIONSSD UpconversionThe 7900 module can be utilized to upconvert SD video from many different source types.As shown in the example below, the S

SD Aspect Ratio ConversionThe 7900 module can perform standard definition aspect ratio conversion to convert theaspect ratio of the SD input signal to

INSTALLATIONSubmodule InstallationAn optional audio submodule installs on the component side of the 7900 module circuitboard. If the option is ordered

Model 7900 HD Up/Down/Cross ConverterConnect an HD or SDserial digital signal to theHD/SD In BNC.Connect HD or SD output destinations to BNCs HD/SD Ou